Jacket Delta OL of the Slovenian company UF PRO it will keep your comfort of work during low temperatures and heavy snowfall or rain intact. Delta OL will provide you with the necessary protection so that you can fully concentrate on your tasks and the work at hand. The outer material used is a two-layer laminate Ripstop makes the Delta OL 3.0 jacket is windproof and waterproof. Remarkable thermal insulation G-Loft it creates a three-dimensional structure of various polyester fibers that retains maximum dry air. The insulation layer in the torso area of 145 g / m2 is thicker than in the sleeves of 110 g / m2. G-loft fibers also retain their structure when wet. Due to the so-called The “memory effect” always returns to its original shape – even after many washes and difficult use. Elements that are more prone to wear and tear – such as the elbows and lower back – are additionally reinforced with fabric 500 Denier Cordura. Thanks to its anatomical cut, the Delta OL 3.0 Jacket has a tight fit, allows full freedom of movement and remains tight enough to accommodate additional equipment such as plate supports or Chest-Rigs. To keep the core of the body warm and to provide additional freedom of movement in the shoulder area, the jacket has two levels of protection against the cold. The hood of the jacket is adjustable in width and is removable. The collar is lined with COCONA® 37.5 ™ microfleece material



The jacket has 2 front pockets, 2 on each sleeve and 2 inside pockets. All outer pockets are equipped with high-quality branded zippers. Zippers (except inside pockets) are taped for better handling.

Front pockets

Very spacious pockets with oblique openings are located on the left and right front part of the jacket (26cm effective opening). The pockets have waterproof polyurethane laminated zippers. When closed, the zippers are hidden in the fold of the outer fabric. The pocket lining is made of COCONA® 37.5 ™


Upper sleeve pockets

Both sleeves have pockets with vertical zippers (approx. 14 cm of effective opening). The slider is covered with a lath. The pocket lining is made of COCONA® 37.5 ™


Lower sleeve pockets

Both sleeves have zipped lower pockets (approx. 13 cm of effective opening). The slider is covered with a lath. The pocket lining is made of COCONA® 37.5 ™


Internal pockets

A large mesh pocket is located on the left and right sides of the inside of the jacket, with horizontal and vertical access. The pocket openings are equipped with zippers (both vertical and horizontal opening of approx. 20 cm)

Clasp the jacket

The jacket is equipped with a waterproof polyurethane laminated Purl zipper with a double zipper. At the bottom of the zipper, the jacket has a 4 cm wide strip made of an external material. The strip is double and vertically quilted several times at intervals of 5 mm. The front zipper ends at the top with a flap made of a strip of external material. The zipper slider has a tape for better handling.


They are located on the sides of the jacket, under the arms. They are equipped with zippers with double waterproof zippers and mesh lining. Zipper sliders are taped for better handling.

Wrist warmers

At the bottom of the sleeves there are cuffs made of elastic knit, 18 cm long and 10 cm wide, which can be pulled over the wrists. The wrist opening is 7 cm long.

Sleeve width adjustment

The sleeves in the lower part have slats for adjusting the width made of abrasion-resistant polyamide material with Velcro at a length of 15 cm. 2.6 Adjusting the width of the bottom of the jacket There is an elastic drawstring at the bottom of the jacket, the length of which can be adjusted on the sides of the jacket. The string runs in a tunnel made of outer material with a rubber end.


The hood is anatomically shaped and lined with quilted insulation material. It has horizontal and vertical elastic strings to adjust the hood to the shape of the head. They are adjusted with locking stoppers. Elastic cords have rubber tips. At the front edge of the hood there is a reinforcing wire with the ends secured against puncture. The hood is fastened to the jacket with a thin zipper. In the part that covers the chin, there are 4 press studs for fastening and adjusting the collar width. On the left and right sides of the front zipper there are press studs for attaching the chin guard to the front of the jacket.


The jacket has a hanging loop made of the outer material in the collar seam.


There are Velcro areas on the upper sleeve pockets and on the right side of the chest.

Dimensions: Upper arm pocket 14cm x 9.5cm (X-stitching) Chest 12cm x 3.8cm (X-stitching)


WINDSTOPPER®, two-layer laminate, 100% polyamide ripstop fabric, 100% ePTFE membrane

G-Loft, 100% polyester non woven

100% Cordura®

Additional information

Weight 1 kg
Dimensions 60 × 50 × 80 cm



There are no reviews yet.


Your email address will not be published. Required fields are marked *